| ALSO SEE 'CARBS' PAGE FOR CARBS, INJECTION PARTS, NITROUS, AND INLET MANIFOLDS......... |
|
| Ford Crossflow Rear wheel drive Lightened and balance flywheel to suit std 7.5" clutch, weighs 15lb / 6.75kg - mating surface not scored, ready to use. |
£59.00 |
| Ford Crossflow Rear wheel drive oil pump, as new never fitted. Standard as far as we can see. |
£25.00 |
| Ford Crossflow 5-speed type 9 clutch friction plate - 23 spline x 1" centre, 7.5" diameter, 2 available both as new never fitted, 1x EBC and 1x LUK brand |
£25 ea |
| Twin 40DCNF Downdraught Weber Carbs fitted to Ford CVH manifold, 30mm chokes fitted, come with a nearly new HOLLEY Chromed fuel pressure regulator, bracket and Mr.Gasket baby fuel pressure gauge and includes a nearly new FACET Cube type fule pump and fittings, throttle cable bracket, throttle cable and heatshield (bolts to rocker cover screws). Will run as it is, but needs air filters and will require a rolling road set-up / jetting session. Photo available on request. |
£249.00 |
| RS1600i Escort Mk3 original FORD finned Alloy rocker cover with original oil filler cap. Nice clean condition, photo available on request. |
£95.00 |
| Crossflow Hot-Rod cylinder head - Full race - Stainless steel valves 41.3mm inlets and 35mm exhaust, huge ports, opened out head face waterways, shimmed up double valve springs, very shallow combustion chambers, head stamped with chamber volume 7.5cc. Ex 14 mile oval circuit race car. Pics available on request. New cost on a head like this is £700-£900 exchange. |
£395.00 |
| X-Flow / Lotus Twin-Cam / BDA Burton Performance billet alli thermostat housing - absolutely as new and never fitted |
£30.00 |
| X-Flow Burton Performance Billet steel crankshaft pulley absolutely as new and unfitted still in original polythene bag. |
£35.00 |
| RS Turbo Series 2 standard Mfi cylinder head, 1989 casting, with calves / springs but no cam / followers / rockers. Super-clean condition - all nice and silver casting i.e. no caked on oil deposits under the rocker cover. Looks recently reconditioned but no paperwork to prove. Photo available on request. |
£75.00 |
| FIESTA RS TURBO EFi CVH Cylinder head, stainless steel inlet valves fitted, standard cylinder head, unmodified and believed un-skimmed from new. Removed due to bottom end failure. All good threads. No rockers or cam/followers fitted. |
£75.00 |
| Fiesta Turbo Efi Cylinder head, just rebuilt with new valves / guides etc, standard spec, never fitted since rebuild done by Jenkins Engineering in Whitton near Twickenham, Cost £350, includes a new cam and followers. |
£225.00 |
| FORD CROSSFLOW NEW CHROMED ROCKER COVERS, inc twist-on filler cap (also chromed) - 1100 / 1300 / 1600 |
£33.95 |
| Ford CVH Lean burn cylinder head, inc cam but no followers or rockers, no exhaust valves fitted, 1988 casting, heart shaped combustion chambers |
£40.00 |
| Side-exit cap type LUCAS distributor for 1600 CROSSFLOW - non-vaccuum, with LUMENITION electronic ignition fitted, complete distributor ready to fit. Suit fast road engine. Includes clamp and drive gear. Photo avail on request. Marked 103FXPS on casing. |
£95.00 |
| FORD CLUTCH FRICTION PLATE - This is new and never fitted, 20 spline x 8.5", likely to fit 1600 GT / 'S' Pinto Capri Mk1/2/3, Cortina Mk3 1600 GT Pinto |
£15.00 |
| FORD CROSSFLOW PIPER-CAMS CAM-FOLLOWERS - FOR LATER 711M ENGINES (Wider stem) - Part no. FOLFW - NEW + BOXED SET OF 8 |
£47.95 |
Non-Vaccuum original LUCAS FORD OHV distributor for Crossflow or possibly TWIN CAM Lotus / BDA or possibly Anglia 105E ? Stamping on plate reads 40655J. Needs new drive gear (cracked) - has points and condensor fitted, no play in top of shaft. Also comes with clamp. Click photo for bigger image.
|
£30.00 |
| DISTRIBUTOR FOR 1300 CROSSFLOW part no 761F JA - good drive gear, no play in shaft, with condensor, good vaccuum advance unit, but no points / cap or rotor arm. Good used. |
£25.00 |
NEW FELPRO HIGH PERFORMANCE HEAD GASKET FOR FORD CROSSFLOW ENGINES - WILL WORK ON STANDARD AND BIGGER BORES UP TO 83.3MM / 3.28 INCHES DIAMETER.
THE STANDARD 1300 / 1600 CROSSFLOW BORE IS 80.98MM / 3.188 INCHES SO THESE GASKETS ARE GOOD FOR STANDARD BORE OR UP TO A 90 THOU OVER BORE (1700cc ENGINES)
|
£28.95 inc VAT |
| Crossflow Oil pump, second hand, for early engines with non-spin-on type filter i.e. early twin cams etc. Has a sandwich plate fitted with push-on fittings for an oil cooler. Genuine FORD, part no. 105E-6604-B |
£15.00 |
| 1600 CVH standard lean-burn
(heart shaped combustion chambers) cylinder head, good
used |
£75.00 |
| Crossflow BOSCH points distributor, as fitted to 1.1 and 1.3 Fiestas, part number 0231-170292 / 81BF12100AA |
£25.00 |
| XR3i CVH distributor, nearly new with electronic ignition module (84SF-12K059AA), cap, vaccuum canister, cap and rotor arm. Part no 84SF12100MAOHD. Will give warranty. |
£49.00 |
| FORD Crossflow 1100 distributor - BOSCH Fiesta points type, part no - 81BF12100AA - perfect drive gear, no play in shaft, with points and condensor. |
£25.00 |
| Crossflow
inlet manifold for twin choke Weber (original Ford as
fitted to Mk2 Escort 1600 + Mk1 Mexico + X-Flow Capri
GT), good condition with 4 new nylocks |
£SOLD |
| Sierra Cosworth DISTRIBUTOR with sensor and drive gear. |
£45.00 |
| Ford Pinto
/ Crossflow / 3.0 V6 standard cyl. heads (used)
all |
£40.00 |
| FORD 351 ci V8 Points distributor, Motorcraft / Bosch, part no. 76DA-12100-EA / BOSCH Number 9230063820. No vaccuum canister fitted but looks fine other than that. No play in shaft. Includes points, condensor, drive gear. No cap. Made in Australia. |
£35.00 |
| Crossflow standard flywheel, good used |
£20.00 |
| |
|
| MANY OTHER FORD ENGINE PARTS new and used - standard and Performance - too many to hist here, PINTO - CROSSFLOW - CVH - V6 - ROVER V8 - ZETEC |
£CALL |
